Datalink Systems i50 Dokumentacja Pobierz pdf (Strona 60)

i50 Manual (5.10)

Page 60

www.datalinksystemsinc.com

Name

Description

Default

159

I_MAXCORNER

Max allowed cornering g-force (1/100 g). Set to zero to disable

160

I_USEBATT

Voltage (1/10 V) above which engine is running. Set to zero to disable. When

disabled, unit will use Engine On input or IGN to assume engine running. This

setting is used to count engine hours and calculate drive and idle times.

130

161

I_ACCELX

Accelerometer rotation around X axis (radians*10000). Set to zero to

recalibrate

162

I_ACCELY

Accelerometer rotation around Y axis (radians*10000). Set to zero to

recalibrate

163

I_MAXTILT

Max allowed tilt when stationary (degrees). Set to zero to disable

164

I_MOTIONSENSE

Set g-force required to trigger motion detection (approx 1/1000 g). Range 1-255

165

I_TRANSUDPPORT

UDP port for sending and receiving transparent data during a dial-up or Wi-Fi

connection. Set to zero to disable

4001

166

I_EMAILUDPPORT

UDP port for sending and receiving message/email data during a dial-up or Wi-

Fi connection. Set to zero to disable

4000

167

I_FUEL1

Engine Hours (1/100 gallons)

168

I_FUEL2

169

I_ADVANCED

Advanced GPS report. Bit 2=Digital I/O States. Bit 3=Cell Info. Bit 4=ADC2. Bit

5=ADC1. Bit 6=Battery Voltage. Bit 7=Temperature. Bit 8=Speed. Bit

9=Altitude. Bit 10=Heading. Bit 11=GPS HDOP

170

I_SIGNTRANS

Bit 1=Send NTCIP data in UDP format. Bit 0=Enable transparent access to sign

terminal

171

I_SIGNMSG

NTCIP Sign Message Number. Set to zero to use AMSIG protocol

172

I_SIGNID

NTCIP Sign ID

173

I_KENWOOD

Kenwood settings. Bit 7=Long data. Bit 6=NXDN. Bit 5=Software ACKs. Bit

4=WAN mode. Bit 3=Transparent. Bit 0=KW Prot Ver 1

193

174

I_RFBITS

RF COM settings. Bits 0-1=(Data bits-5). Bit 2=Extra Stop bits. Bit 3=Parity. Bit

4=Even

175

I_UNIT

Kenwood unit number used as destination when sending data (0000, 1000-

4999 for Fleetsync, or 00000-65519 for NXDN)

176

I_FLEET

Kenwood fleet/ID type for sending data (0, 100-349 for Fleetsync, or 0=GID,

1=UID, 2=Broadcast for NXDN)

177

I_ENGINEVE

Engine volumetric efficiency (%)

178

I_ENGINEDISP

Engine displacement (cc)

3000

179

I_LOWBATT

Low battery warning (1/10 V). Set to zero to disable

180

I_OUTPUT4

Output 4 Setting. See note at bottom for values

181

I_OUTPOLARITY4

Output 4 polarity (0=Low 1=High)

182

I_VOUT

VOUT function. See I/O note at bottom for values

183

I_VOUTPOLARITY

VOUT polarity (0=Low 1=High)

184

I_ADC1HIGH

Trigger event if ADC1 exceeds this voltage (1/10 V). Set to zero to disable

185

I_ADC1LOW

Trigger event if ADC1 drops under this voltage (1/10 V). Set to zero to disable

186

I_ADC2HIGH

Trigger event if ADC2 exceeds this voltage (1/10 V). Set to zero to disable

187

I_ADC2LOW

Trigger event if ADC2 drops under this voltage (1/10 V). Set to zero to disable

188

I_DEBOUNCEADC1

Debounce time (ms) for ADC1 changes

100

189

I_DEBOUNCEADC2

Debounce time (ms) for ADC2 changes

100

190

I_NOGPS

Send alert if GPS signal is unavailable for this period (sec). Ver 4.88 and later

only increment this counter while vehicle is moving.

191

I_RXUNIT

Kenwood unit number used to listen for data from base radio (1000-4999 for

Fleetsync, or 00001-65519 for NXDN). Set to zero to use I_UNIT

192

I_RXFLEET

Kenwood fleet ID used to listen for data from base radio (Fleetsync only). Set to

zero to use I_FLEET

1 2 ... 55 56 57 58 59 60 61 62 63 64 65

Komentarze do niniejszej Instrukcji

Brak uwag

Datalink Systems i50 Dokumentacja Strona 60

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Nawigatory Datalink Systems i50